check engine VOLKSWAGEN PASSAT 1996 B3, B4 / 3.G Service Workshop Manual

Downloaded from www.Manualslib.com manuals search engine Suspension, Wheels, Brakes, Steering

00 - General, Technical data
Suspension, Wheels, Brakes, Steering
Technical data
Steering
Brakes
Wheels, tires
40 - Front suspension
Front Wheel Suspension, Shafts and Axle
Front suspension, servicing (Base suspension)
Sub-frame, stabilizer bar and control arm (Base suspension)
Ball joint, checking (Base and Plus suspension)
Reworking cap nut in side member (Base and Plus suspension)
Wheel bearing, suspension strut and drive shaft, removing and installing (Base
running gear)
Front suspension strut, servicing (Base and Plus suspension)
Front suspension, servicing (Plus suspension)
Sub-frame, stabilizer bar and control arm, removing and installing (Plus
suspension)
Ball joint, removing and installing (Plus running gear)
Wheel bearing and suspension strut, removing and installing (Plus suspension)
Drive shaft, removing and installing (Plus running gear)
Drive shaft, repairing
Outer constant velocity joint, checking
Inner constant velocity joint, checking
Drive shaft with tripod joint, repairing
Drive axle with triple-rotor joint, removing and installing
Drive axle with triple-rotor joint, servicing
Triple-rotor joint, disassembling
Triple-rotor joint, assembling
42 - Rear suspension
Rear Wheel Suspension, Shafts and Axle
Rear axle, servicing (vehicles with front wheel drive)
Reworking cap nut in side member (front wheel drive vehicles)
Suspension strut, disassembling and assembling (front wheel drive vehicles)
Wheel bearings, servicing
Drum brakes (front wheel drive vehicles), wheel bearings, servicing
Wheel bearings, servicing - disc brakes (front wheel drive vehicles)

Downloaded from www.Manualslib.com manuals search engine Front brakes, servicing (Teves/Ate)
Brake pads, removing and installing
Rear wheel brakes, servicing (drum brakes)
Brake shoe adjustment, releasing
Rear wheel brakes, servicing
Brake shoes, removing and installing
Parking brake, adjusting (drum brakes)
Rear wheel brakes, servicing (disc brakes)
Girling rear wheel disc brakes (front and four wheel drive vehicles)
Brake pads, removing and installing
Parking brake, adjusting (disc brakes)
Parking brake lever assembly overview
Brake pedal/brake servo, removing and installing
Brake pedal, removing and installing
Brake Light Switch, adjusting
47 - Brakes - Hydraulic components
Assembly overview: brake master cylinder/brake servo
Girling front brake caliper, servicing
Front brake caliper pistons, removing and installing
Front brake caliper, servicing (Teves/Ate)
Rear brake caliper, servicing
Rear brake caliper piston, removing and installing
Pre-bleeding brake caliper
Brake pressure regulator, checking and adjusting
Vehicles without ABS, vehicles with ABS, ABS/EDS, Teves 04
Load dependent brake pressure regulator specifications
Adjusting regulator
Brake system, bleeding
Brake system, bleeding (vehicles with and without ABS, ABS/EDL)
Brake system, bleeding (with pressure bleeder VAS 5234)
Brake system, bleeding (without pressure bleeder)

Downloaded from www.Manualslib.com manuals search engine 48 - Steering
Steering
Assembly overview: steering column, column tube, steering wheel and airbag
steering wheel
Airbag unit, removing and installing
Airbag steering wheel, removing and installing
Airbag Spiral Spring, removing and installing
Column tube for height adjustable steering wheel, removing and installing
Pump delivery pressure, checking
Power steering gear, removing and installing
Assembly overview: power assisted steering box (TRW)
Power steering gear, adjusting (TRW)
Power steering gear, disassembling and reassembling (TRW)
Power steering gear, disassembling
Inner sealing ring for toothed rod, pulling out
Checking toothed rod for scoring
Sealing ring on toothed rod, replacing
Sealing rings, installing on toothed rod piston
Power steering gear, assembling
Inner sealing ring for toothed rod, installing
Toothed rod, installing in housing
Adhesive tape, applying
Power steering gear, adjusting with new toothed rod
Assembly overview: power steering gear (ZF)
Power steering gear, adjusting (ZF)
Power steering gear, disassembling and reassembling (ZF)
Power steering gear, disassembling
Checking toothed rod for scoring
Sealing ring on toothed rod, replacing
Power steering gear, assembling
Tie rods, removing and installing (power steering gear - TRW and ZF)
Left-hand tie rod length, checking and adjusting
Assembly overview: vane pump, reservoir and hydraulic lines (vehicles with 4-
Cyl. engines)
Assembly overview: Hydraulic lines, reservoir (vehicles with 4-Cyl. engines)
Power steering vane pump, removing and installing (vehicles with 4-Cyl. engines)
V-belts, tensioning (4-Cyl. engines)
Assembly overview: Pressure and cooling lines (vehicles with VR6 engine)
Power steering vane pump, removing and installing (vehicles with VR6 engine]

Downloaded from www.Manualslib.com manuals search engine 40-3

1 - Hex bolt, 35 Nm (26 ft
lb)
2 - Ball joint Checking Page 40-10 Check rubber boot for
damage and if necessary, replace ball joint Mark installation
position. If replaced
set to center of
elongated hole and
check toe Elongated holes are
not for camber
adjustment. Failure to observe this instruction may result in damage
to drive shafts!
3 - Captive lock nuts
4 - Air deflector plate Secured to control arm by clip
5 - Control arm Page 3 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-5

Repair Manual, Engine
Mechanical, Repair Group 10 12 - Connecting link
mounting Conical side toward
control arm
13 - Washer Collar faces away from mounting
14 - Self-locking hex nut, 25 Nm (18 ft lb)
15 - Sub-frame Removing and
installing with
assemblies installed:
supporting assemblies
Fig. 5 Remove sub-frame
from below with VAG
1383 (with control arm
but without steering
gear). After installing
check position of
steering wheel and
align front end. Aligning engine-
transmission assembly Page 5 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-10

Ball joint, checking (Base and Plus
suspension)

Checking axial clearance Checking radial play - Forcibly pull ball joint down and press up again. Note: - Press lower part of wheel outward and inward. There must be no perceptible or visual "play"
during either test. Observe ball joint during checks. Take into account possible existing wheel bearing
play or "play" in upper suspension strut mounting. Page 10 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-23

Front suspension strut,
servicing (Base and Plus
suspension)
1 - Shock absorber Can be replaced
individually Check shock absorber
for leaks and noises After replacing, adjust
camber and toe
Page 44-1 2 - Buffer stop
3 - Protective sleeve Page 23 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-27

Sub-frame, stabilizer bar
and control arm,
removing and installing
(Plus suspension)
Notes Page 40-2 1 - Hex bolt, 35 Nm (26 ft
lb)
2 - Ball joint Checking Page 40-10 Check rubber boot for
damage and if necessary, replace ball joint Removing and
installing Page 40-33 Mark installation
position. If replaced
set to center of
elongated hole and
check track
3 - Self-locking hex nut, 45 Nm (33 ft lb)
4 - Captive locknuts Page 27 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-30

Repair Manual, Engine
Mechanical, Repair Group 10 20 - Vibration damper Not installed on
vehicles with VR 6
engine
21 - Sub-frame Removing and
installing with
assemblies installed:
supporting assemblies
Fig. 4 Remove sub-frame from below with control arm but without
steering gear using transmission jack VAG 1383 or equivalent.
After installing check
position of steering
wheel and align front
end. Aligning
engine/transmission
assembly
22 - Stabilizer bar mounting 23 - Stabilizer bar 24 mm diameter 24 - Cap nut Reworking in side
member Page 40-11 Page 30 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-47

1 - Circlip Always replace Remove and install
with VW161 a
2 - Gasket Always replace. Pull
off protective foil and
stick onto joint. (Only
on 100 mm diameter
constant velocity joints
3 - Inner constant velocity
joint 100 mm diameter Only replace complete Pressing off Fig. 3 Pressing on Fig. 4 Greasing Notes
Page 40-46 Checking Page 40-62 4 - Dished washer Inner diameter splined Installation position:
outer diameter
(concave side)
contacts constant
velocity joint Page 47 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1